Ф 7.11-12

 

M.AUESOV SOUTH KAZAKHSTAN STATE UNIVERSITY

 

СHЕМIСАL-ТЕСНNОLОGIСАL  FАСULТY

 

DEPARTMENT OF TECHNOLOGY OF OIL, GAS AND POLYMERS

 

 

 

           Agreed

Deаn of the сhеmiсаl-tесhnоlogiсаl  fасulty

_________Nazаrbeсovа S.Р.

“___” _____09_____2009y

 

 

 

 

 

 

SYLLABUS

 

on discipline « Environmental problems of petroleum chemistry »

speciality 050721 – Chemical technology of organic substаnces

 

 

Form of education     full-time

Course        IV

Semester    7

Credits number__3

Lectures      30 hours

Practice      15 hours

IWST         45 hours

IWS           45 hours

 

Quantity of  border modules  _2

Form of final inspection    examination

 

 

 

 

 

 

 

SHYMKENT – 2009

 

Educational-methodical complex has been prepared by Assistant Professor, Cand. of Sci. (Eng.) Bekmukhanbetova D.B., Аbduhalikova  I.

on the basis of the typical programme on the discipline  «Environmental problems of petroleum chemistry» for students of speciality 050721 – Chemical technology of organic substаnces (the report # 1 26.08.2006у).

 

Was approved at the meeting of department of oil, gas and polymers technology “27” 08 2009, the report # 1

 

 

Chair of the department                                                         Sakibaeva S.

                        Cand. of Sci. (Eng.), docent

 

The syllabus was approved by the methodical commission of  the сhеmiсаl-tесhnоlogy fасulty  “29” 09 2009, the report # 1

 

Chairman:                                                                  Ibrаgimovа  G.

 

Administrator                                                 Bolусвеk  А. 

 

 

1. The lecturer: Аbdukhalikova  I., the phone 21-19-66,

    room 311 B. Time of stay  from 1330 o'clock till 1630 o'clock.

2. Time and a place of carrying out of the course.

    Time of carrying out of training - from 1235 o'clock till 1625 o'clock.

3. An actuality and necessity of studying of a course.

3.1. The purpose and tasks of a course.

The purpose of discipline "Environmental problems of petroleum chemistry" is to study ecological aspects of production and consumption of power resources in the branches of oil refining and petroleum chemistry industries.

Tasks of the discipline studying

The main goals of discipline are to learn students:

-           the ecological aspects of use of power resources;

-           the methods of deactivation and reclamation of waste products during monomers, polymers, elastomers synthesis.

-           to analyze the ecological consequences of sewage pollution by the surface-active substances;

-           to analyze environmental problems of oil production, transportation and oil and gas refining;

-           to provide for all probable negative consequences of ecological influence of petroleum and gas in connection with a growth of volumes of  production and refining of oil in Kazakhstan;

-           to study principles of toxic compounds  formation  during consumption of oil products  and to know theirs MAC value;

 

3.2. The maintenance of a course.

 In order to successful study course it is necessary to systematically work and use the new educational methods and practice. One should take into account the individual work of students under teacher control.

4. Previous elements of a course.

Course is based on disciplines «Up-to-date processes of petroleum chemistry»", «Production of the resin and fiber from oil chemical stock», «Synthetic detergents», «Equipments specification», «Chemistry and technology of synthetics rubber», «Technology of  high-molecular compound», "Organic chemistry" "Ecology" etc.

Ecological aspects of use of power resources. The main ecological characteristics of petroleum, gas and coal deposits of Kazakhstan.

Normalization and physical and chemical methods of determination of pollution in the atmosphere. Methods of determination of pollution in the atmosphere.

5.Роst рroреrtiеs of a course. Methods of sewage treatment from surface-active substances (SAS), which is used in oil and gas recovery. Ecological consequences of water resources pollution. Physical and chemical methods of sewage treatment from substances (SAS).

The environment consists of three important spatial elements, which are air, water, and soil. Environmental protection engineering has to protect air, water, and soil against any serious disturbance of its own natural equilibrium. Technology supplies the tools but it is man who has to apply these tools for the benefit of its environment and his future.

The problems of environmental protection can only be solved by the coordinated endeavors of various engineering and scientific disciplines: physics, chemistry, medicine, biology, chemical engineering, and social sciences. For any single discipline it is possible to solve the problems. Many scientific and engineering disciplines will have to contribute to the solution of the problems. The engineers contribution will be primarily the development, design, and operation of equipment for the abatement of harmful emissions. 

 

6. Distribution of hours under credits and kinds of lessons

 

Sеmester

Quantity of credits

Kinds of lessons

IWS

Total

Form of inspection

 

 

Lecture

Practice

IWST

 

 

 

У11

3

30

15

45

45

135

Examination

 

7. The schedule of carrying out of training includes:

7.1. Syllabus of  lectures

 

Quantity of lecture hours         30  

Group             СНТ-06-7ка2                           

 

№

Date

Number, the name of the module and theme of lecture

The form of carrying out

of lecture

Conducting VAX and methods of activization of cognitive activity

Knowledge and the skills formed by students

1

2

3

4

5

6

Module 1. Section 1.  Oil refining and petroleum chemical factories are a source of environmental pollution.

1.

3.09.09

Ecological aspects of use of power resources. The main ecological characteristics of petroleum, gas and coal deposits of Kazakhstan. Sources of atmosphere pollution. Pond and soil pollutions.

Problem lecture

Slide 1

Sources of atmosphere pollution. Pond and soil pollutions.

2.

3.09.09

Classification of atmospheric effluents. Hydrocarbons and their derivatives.

Problem lecture

Poster1

Hydrocarbons and their derivatives. apparatuses.

3.

10.09.09

Photochemical transformations of pollution in the atmosphere. Reactive substances

Problem lecture

 

Reactive substances

4.

10.09.09

Problem of effluents decrease of hydrocarbons and their derivatives in the atmosphere. Oxidizers and photochemical smoke.

Lecture-Information

 

Oxidizers and photochemical smoke.

 

5.

17.09.09

Problem of effluents decrease of hydrocarbons and their derivatives in the atmosphere. Oxidizers and photochemical smoke.

Lecture-Information

 

Oxidizers and photochemical smoke.

 

Module 1. Section 2. Sewage treatment.

6.

17.09.09

Water pollution.

Problem

 

Water pollution.

7.

24.09.09

Mechanical cleaning

 

Problem

 

Mechanical cleaning

8.

24.09.09

Physical-chemical methods of sewage treatment

Problem lecture

Slide 2

Physical-chemical methods of sewage treatment

9.

01.10.08

Biological sewage treatment

Problem lecture

Slide 3

Biological sewage treatment

10

01.10.09

Sewage treatment from soluble organic substances. Biological sewage treatment.

Problem lecture

Slide 4

Biological sewage treatment.

 

11

08.10.09

Sewage treatment from soluble organic substances. Biological sewage treatment.

 

Problem lecture

Slide 5

Sewage treatment from soluble organic substances.

12

08.10.09

Sewage treatment by means of membrane methods. Creation of the closed systems of water supply.

Lecture-Information

 

Creation of the closed systems of water supply.

13

15.10.09

Sewage treatment by means of membrane methods. Creation of the closed systems of water supply.

Lecture-Information

 

Creation of the closed systems of water supply.

Module 2. Section 1.  Air pollution control equipment

14

15.10.09

Air pollution control equipment.

Problem lecture

Slide 6

Air pollution control equipment.

15

22.10.09

Dust emission abatement

Problem lecture

Slide 7

Dust emission abatement

16

22.10.09

Dust removal equipment

Information

Slide 8

Dust removal

17

29.10.09

Dry dust removal equipment.

Information

 

Dry dust removal equipment.

18

29.10.09

Dry dust removal equipment.

Information

 

Dry dust removal equipment.

19

05.11.09

Wet dust removal equipment

Information

Slide 9

Wet dust removal equipment

20

05.11.09

Wet dust removal equipment.

Information

Slide 10

Dry dust removal equipment.

21

12.11.09

Adsorption processes and equipment

Information

 

Adsorption processes and equipment

22

12.11.09

Adsorption processes and equipment

Information

 

Adsorption processes and equipment

23

19.11.09

Adsorption and recovery of organic gases and vapors.

 

Information

 

Adsorption and recovery of orga-nic gases and vapors.

24

19.11.09

Adsorption of H2S and CS2 from waste gases

Information

 

Adsorption of H2S and CS2 from waste gases

Module 2. Section 2. Soil contamination

25

26.11.09

Soil contamination

Information

Slide 11

Soil contamination

26

26.11.09

Soil contamination

Information

 

Soil contamination

27

03.12.08

Sludge neutralization

Information

 

Sulfur Recovery and  Pollution  Control  Processes

28

03.12.09

Storage of oil and oil products.

Information

Slide 12

Claus*s method of sulfur recovery

29

10.12.09

Storage of oil and oil products.

Information

 

Storage of oil and oil products.

30

10.12.09

Minamata disease. Mercury globe pollution

 

Information

 

Storage of oil and oil products.

7.2. The list of tasks to the students on practice

 

 

№

 

Dаtе

Topic and ISW content  

according to module

Task

The form

Control form

What student should know

1

2

3

4

5

6

Module 1. Section 2.  Sewage treatment

1

3.09.09

 

Water pollution.

 

1-L-3

Calculation of the task

Control work

Water pollution.

 

2

10.09.09  Physical-chemical   methods of sewage treatment.

 

2-L-3

Calculation of the task

Control work

Physical-chemical methods

 

3

17.09.09 Biological sewage treatment

3-L-3

Calculation of the task

Control work

Biological sewage treatment

 

4

24.09.09

Sewage treatment from soluble organic substan-ces. Biological sewage treatment.

 

4-L-3

Calculation of the task

Control work

Biological sewage treatment.

 

5

1.10.09

            Sewage treatment by

means of membrane methods. Creation of the closed systems of water supply.

 

5-L-3

Calculation of the task

Control work

Creation of the closed systems of water supply.

 

6.

 8.10.09  Water pollution.

 

6-L-3

Calculation of the task

Control work

Water pollution.

 

Module 2. Section 1. Air pollution control equipment

7.

 15.10.09 Dust emission abatement

 

7-L-3

Calculation of the task

Control work

Dust emission abatement

 

8.

  22.10.09 Dust removal equipment

 

8-L-3

Calculation of the task

Control work

Dust removal equipment

 

9.

 29.10.09 Dry removal equipment.

 

9-L-3

Calculation of the task

Control work

Dry dust removal equipment.

 

10.

 05.11.09 Wet dust removal equipment

 

10-L-3

Calculation of the task

Control work

Wet dust removal equipment

 

11

12.11.09 Adsorption processes and equipment

11-L-3

Calculation of the task

Control work

Adsorption processes and equipment

12

  19.11.09 Adsorption and recovery of organic gases and vapors.

11-L-3

Calculation of the task

Control work

Adsorption and recovery of organic gases and vapors.

 

13

  26.11.09   Adsorption of H2S and CS2 from waste gases

12-L-3

Calculation of the task

Control work

Adsorption of H2S and CS2 from waste gases

Module 2. Section 2. Soil contamination

14

 03.12.09    Soil contamination

12-L-3

Calculation of the task

Control work

Soil contamination

15

 10.12.09 Storage of oil and oil products.

13-L-3

Calculation of the task

Control work

Storage of oil and oil products.

 

7.3 The list of tasks to the students on IWST

           

№

Topic and ISW content according to module

Task for ISW T

Literature

Control form

What student

should know

Dеаd

linе

 

1

2

3

4

5

6

Module 1. Section 1. Oil refining and petroleum chemical factories are a source of environmental pollution

1

Ecological aspects of use of power resources. The main ecological characteristics of petroleum, gas and coal deposits of Kazakhstan.

 

Glossary on the theme.

 

1-6

Defense

The main

ecological

characteristics

of petroleum,

gas and coal

deposits of

Kazakhstan.

7.09.09

 

 

 

 

 

 

2

Ecological aspects of use of power resources. The main ecological characteristics of petroleum, gas and coal deposits of Kazakhstan.

 

Glossary on the theme.

 

1-6

Defense

The main

ecological

characteristics

 of petroleum,

 gas and coal

deposits of

Kazakhstan.

14.09.

09

 

 

 

 

 

 

 

3

Classification of atmospheric effluents. Hydrocarbons and their derivatives.

Glossary on the theme.

2-7

Defense

Hydrocarbons

and their deri-

vatives.

21.09.

09

 

 

 

4

Photochemical transformations of pollution in the atmosphere. Reactive substances.

Glossary on the theme.

3-7

Defense

Reactive

substances.

27.09.

09

 

 

5

Classification of atmospheric effluents. Hydrocarbons and their derivatives.

Glossary on the theme.

2-7

Defense

Hydrocarbons

and their deri-

vatives.

5.10.09.

 

 

6

Photochemical transformations of pollution in the atmosphere. Reactive substances.

Glossary on the theme.

3-7

Defense

Reactive

 substances.

8.10.09

 

Module 1. Section 1. Sewage treatment

   7

Water pollution.

Glossary

 

3-9

Defense

Water pol-

lution.

12.10.09

 

   8

Water pollution.

Glossary

 

3-9

Defense

Water pol-

lution.

15.10.09

 

9

Mechanical cleaning

Glossary

 

3-9

Defense

Mechanical

cleaning

19.10.09

 

10

Physical-chemical methods of sewage treatment

Glossary

3-9

Defense

Physical-Che-

mical methods

of sewage

treatment

23.10.09

 

 

 

11

Mechanical cleaning

Glossary

 

3-9

Defense

Mechanical

cleaning

26.10.09

 

12

Physical-chemical methods of sewage treatment

Glossary

 

3-9

Defense

Physical-che-

mical methods

 of sewage

treatment

30.10.09

 

 

 

Module 2 Section 1.. Air pollution control equipment

13

Air pollution control equipment.

Glossary

 

7-10

Defense

Air pol-

lution control

equipment

3.11.09

 

 

14

Dust emission abatement

Glossary

 

7-10

Defense

Dust emission

abatement

7.11.09

 

15

Dust removal equipment

Glossary

 

7-11

Defense

Dust removal

 equipment

10.11.09

 

16

Dust emission abatement

Glossary

 

7-10

Defense

Dust emission

 abatement

13.11.09

 

17

Dust removal equipment

Glossary

 

7-11

Defense

Dust removal

equipment

17.11.09

 

Module 2 Section 2. Soil contamination

 

18

Soil contamination.

Glossary

 

8-13

Defense

Soil contami-

nation.

20.11.09

 

19

Sludge neutralization

Glossary

 

9-15

Defense

Sludge neutral-

lization

24.11.09

 

20

Soil contamination.

Glossary

 

8-13

Defense

Soil contami-

nation.

30.11.09

 

21

Sludge neutralization

Glossary

 

9-15

Defense

Sludge neutral-

lization

4.12.09

 

22

Sludge neutralization

Glossary

 

9-15

Defense

Sludge neutral-

lization

11.12.09

 

 

8. Мid- tеrm tеst

Variant 1

Mechanical and physical and chemical methods of sewage treatment.

Clearing from CO2.

Catalytic after-burning.

Methods of processing oil sludge.

 

Variant 2

 

1.          The estimation of internal combustion engines on toxicity of the exhaust gases.

2.          Clearing atmospheric effluents of solid particles.

3.          Biochemical sewage treatment. Neutralization of brines.

4.          Classification of atmospheric effluent. Hydrocarbons and their derivatives

 

Variant 3

 

The characteristic and sources of atmospheric effluent by production and consumption of mineral oil.

Clearing of gases from carbons oxides.

Methods of sewage treatment.

Processing and recycling of tar.

 

 

 

Variant 4

 

1.          Sources and the characteristic of effluent in atmosphere by production and consumption of mineral oil.

2.          Sorption methods of sewage treatment.

3.          Mechanical methods of sewage treatment.

4.          Methods of processing tar.

 

Variant 5

1.          Normalization of the harmful substances polluting the atmosphere, ground and reservoirs.

2.          Ecological aspects of transportation of oil and gas through the basic pipelines.

3.          Clearing gases from NOx.

4.          Devices of wet clearing gases from a dust.

 

Variant 6

1.          Hydrocarbons and their derivatives which are thrown out in atmosphere.

2.          Clearing gases of hydrogen sulphide a method of catalytic oxidations.

3.          Normalization of the harmful substances acting with sewage

4.          Neutralization and processing oil sludge.

 

Variant 7

1.          The reasons of toxic components formation in the exhaust gases.

2.          Decrease in evaporation of mineral oil in tanks during storage.

3.          Problems of nitrogen oxides content decrease in products of combustion.

4.          Influence of hydrocarbonic structure and chemical structure on structure of the exhaust gases. Structure of the exhaust gases of internal combustion engines.

 

Variant 8

1.         Sources and the characteristic of effluents in atmosphere by production and consumption of mineral oil.

2.         Sorption methods of clearing gases from hydrogen sulphide.

3.         Biochemical methods of sewage treatment

4.         Ways of nitrogen oxide decrease in products of boiler-houses combustion of fuels.

 

Variant 9

1.         The characteristic and sources of atmospheric effluent by production and consumption of mineral oil.

2.         Clearing gases from carbon oxide.

3.         Methods of sewage treatment

4.         Recycling the used mineral oil.

 

Variant 10

1.          Photochemical transformations of pollution in atmosphere

2.          Methods of clearing of gases from СО2.

3.          Recuperation of hydrocarbons.

4.          Structure of the exhaust gases of internal combustion.

 

Variant 11

1.          Biochemical sewage treatment. Neutralization of brines.

2.    Recycling and neutralizations of the drilling waste polluted by chemical reagents.

3.         Influence of the exhaust gases of internal combustion engines on the  environment.

4.          Ways of soil clearing from pollution by oil and mineral oil.

 

Variant 12

1.          Ecological aspects of transportation of oil and gas under the basic pipeline.

2.          The estimation of internal combustion engines on toxicity of the exhaust gases.

3.          The problem of effluent decrease of hydrocarbons and their derivatives in  atmosphere.

4.          Recuperation of hydrocarbons.

Variant 13

1.          Mechanical and physical and chemical methods of sewage treatment

2.          Photochemical transformations of pollution in atmosphere

3.          The problem of effluent decrease in an atmosphere of hydrocarbons and their derivatives.

4.          Adsorptive sewage treatment.

 

Variant 14

1.          Sources of environmental contaminations at storage of mineral oil.

2.          Clearing soil, polluted by mineral oil.

3.          Photochemical transformations of pollution in atmosphere.

4.          Photochemical smoke.

 Variant 15

1.          Resource-saving "know-how" of organic substances.

2.          Clearing gases of hydrogen sulphide Н2S.

3.          Biochemical sewage treatment.

4.  The problem of effluent decrease of sulphur dioxide in atmosphere  during  burning fuel in power installations.

 

Variant 16

1.          Catalytic after-burning.

2.          The combination of the high olefins production.

3.          Ways of sour tar recycling.

4.          Clause*s method.

 

Methodical instructions to independent work of students (at the choice of the teacher)

IWS it will be carried out on the certain sections of a course or the through problems covering some of themes, sections or modules. The most research character carries IWS at the certain rate of questions, more often these questions of methodological character.

All kinds of IWS can be carried out by various methodical methods in various combinations.

Most widespread kinds of IWS are:

The formulation of any concept, writing of a brief essay (0,5 pages, no more);

The review on a theme - in writing to write the brief literary review on 1-2 pages on a recommended theme with attraction of an additional material from a seal and information resources of the Internet;

- a spelling of a glossary - a brief explanation of terms and concepts on the given theme, it is possible to replace on crossword puzzle;

presentation - a choice the student of the certain theme for presentation and expression of the vision, understanding or misunderstanding of any aspect considered in presentation. Time of presentation - 8-10 minutes. The presentation by criterion of a degree of disclosing of a theme, the interest caused students, professionalism is estimated;

business game - role or command, developing skills at the student, necessary for the future professional work, sometimes demanding preparation at home or ending in library;

educational concrete situation - a situation demanding answers of the student on questions on it or writing of the vision of a problem;

the group project - in group should be no more than 4-5 person, each group develops the project, for example, how to make our area a zone of business, it is recommended to use the COMPUTER, block diagrams etc. Can be carried out in form CGQ;

the individual project - is carried out by the most prepared students at will, work should differ uniqueness of a theme and research character;

the oral statement of materials (presentation) . Student states a material on the given theme according to questions of self-preparation. Time presentation - 10-15 minutes. It is estimated by the following criteria - as far as the theme is opened and has caused interest environmental (discussion). As far as the literature, in particular additional is used.

Written works (abstracts, an essay) will be carried out at the end of each module. They should include the used sources. Written work should be stated briefly on 1-2 pages, an essay - a maximum on 2 pages and to contain the exhaustive information of a case in point;

tests will be carried out at the end of each module, and also the teacher can lead without the prevention of students five-minute testing on any theme. For all right answers - 5 marks;

abstracts and reports prepare students at a choice (under one abstract from each module). Can prepare group of students, each of which develops one of sections. The abstract should open essence of a question to be maximum informative and to contain own conclusions;

opinions on presentations of students and abstracts each other. The opinion should contain the brief analysis of the received information to reflect weak and strengths of the report;

the decision of problems. Each student receives the individual task which he should execute in writing at the teacher;

drawing up of problems. Students make conditions of problems on a theme which they have passed at lecture. Together with a condition the decision of a problem should be enclosed.

All tasks should be made in time. The tasks executed with delay, automatically will be estimated below (for each delayed day it is removed on 0,1 marks from each task).

For organization of IWS it is necessary:

- to give out task of IWS in the beginning of academic year (semester);

- to develop current and border forms of inspection;

- to establish time of consultations on IWS.

Besides the establishment of requirements and the general expectations is important, i.e. in syllabus the teacher should aim the student on: а) necessity of execution of home works; б) observance of terms of execution; в) preparation and the responsibility.

Interactive methods give students:

- skills of hearing and dialogue;

- skill to empathize other person;

- to understand development of the point of view;

- improve their ability to decide questions and accepted decisions;

- to argue and think analytically;

- to strengthen their ability in formation of consecutive sights on problems of economy as a whole.

 

Requirements and the common expectations (it is filled in view of own requirements and expectations at passage of the given course), an example:

 

To accept active participation in work during lessons, you should be interested in studying questions of a course and assistance to training of group to represent itself as stimulus for other students of group. All tasks should be carried out to established time and by their preparation you should use principles and the concepts received from textbooks and lectures, creatively approaching to investigated and considered problems. On lessons you should come prepared to discuss a material to set concrete questions and critically to approach to the decision of those problems in which decision we are engaged so that you could emphasize all that is necessary for you in the further training and the future professional work. Besides you need to accept responsibility for own training so that during all course we worked in interaction and with understanding.

 

8. The list of the recommended literature

 

8.1. The basic literature

Белов П.С., Голубева И.А., Низова С.А. Экология производства химических продуктов, продуктов из углеводородов нефти и газа. -М.: Химия, 1991. -256с.

Фурсов В.И. Экологические проблемы окружающей среды. -Алма-Ата.:  Ана тiлi, 1991. -191с.

Воробьев Е.И.  и др. Охрана атмосферы и нефтехимия. -Л.: Химия, 1985. -232с.

Беккер А.А., Агаев Т.Б. Охрана и контроль загрязнения природной среды. -Л.: Гидрометиоиздат, 1989. -288с.

Аксенов И.А., Аксенов В.И. Транспорт и охрана окружающей среды. -М.: Транспорт, 1986. -176с.

Лавров Н.В., Розенфельд Э.И., Хаустович Г.П. Процессы горения топлива и защита окружающей среды. -М.: Металлургия, 1981. -240с.

Энергетика и  охрана окружающей среды. Под ред. Н.Г. Залогина., Л.И. Кроппа и Ю.Н. Кострыкина. -М.: Энергия, 1979. -352с.

Голубев И.Р., Новикова Ю.В. Окружающая среда и транспорт. -М.: Транспорт, 1987. -206с.

 

8.2 Additional:

Якубовский Ю. Автомобильный транспорт и защита окружающей среды. -М.: Транспорт, 1979. -198с.

Борадавкин П.Н., Ким Б.И. Охрана окружающей среды при строительстве и эксплуатации магистральных трубопроводов. -М.: Недра, 1981. -161с.

Танатаров М.А. и др. Технологические расчеты установок переработки нефти. -М.: Химия, 1987. -352с.

Химия  окружающей среды. Пер. с англ. под ред. А.П. Цыганкова. -М.: Химия, 1982. -672с.

Скалкин Ф.В., Канаев А.А. Энергетика и окружающая среда. -Л.: Энергоиздат, 1979. -352с.

Сигал И.Н. Защита воздушного бассейна при сжигании  топлива. -Л.: Недра, 1988. -312с.

Отраслевые журналы "Химия и технология топлив и масел" и "Нефтепереработка и нефтехимия".

 

9. A politics of exhibiting of estimations

Principles:

- objectivity;

- transparency;

- flexibility;

- high differentiation.

Includes:

9.1 Rules of an estimation of all kinds of works:

- points are exposed according to the schedule of the inspection of knowledge;

- if the student during all semester has not missed any practical lessons and actively participated on lessons to him in a result the incentive 1 point is added;

- if the student missed lessons for the disrespectful reasons and has not fulfilled them in due time at him the penal point (for 1 miss – 1 point) is removed.

9.2 Criteria of exhibiting of examination estimation:

the minimal point - 20,

the maximal point - 40.

The examination estimation is exposed in view of the current rating.

9.3 Criteria of exhibiting of a final estimation:

56-69 points - it is satisfactory

70-89 points - it is good

90-100 points - it is excellent

 

 

 

9.4 The schedule of the inspection of knowledge of students

 

   

  Department:  TOGP           

      Lectures:  45, IWST:  45,  course:  4, group:  Сh-Т-06-7ка2

      The lecturer: Bekmukhanbetova D. ,Аbdukhalikova  I.

 

Month

September

Oktober

November

December

Week numbers

1.09.-05.09.

07.09.-12.09.

14.09.-19.09.

21.09-26.09

28.09.-03.10.

05.10-10.10.

12.10-17.10

19.10-24.10.

26.10-31.10.

02.11.-07.11.

09.11.-14.11.

16.11-21.11.

23.11-28.11.

30.12.-05.12.

07.12-12.12.

week

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

Inlet control (max / min)

4/2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

practice.(max / min)

 

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

IWS (max / min)

 

 

 1/0,5

 1/0,5

 

  1/0,5

  1/0,5

  1/0,5

 

  1/0,5

 1/0,5

1/0,5

 

  1/0,5

1/0,5

 

 

IWSТ (max / min)

 

 1/0,5

 1/0,5

 

  1/0,5

  1/0,5

  1/0,5

 

  1/0,5

 1/0,5

1/0,5

 

  1/0,5

1/0,5

 

 

Border task (max / min)

 

 

 

2/1

 

 

 

2/1

 

 

 

2/1

 

 

2/1

Marks: max

            min

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

Total control max / min)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

60/30

 

10. A politics of a course (the recommended list)

1. To not be late for lessons.

2. to not talk during lessons, to not read the newspaper, to disconnect a cellular telephone, to not chew a chewing elastic band.

3. on lessons to come in business clothes.

4. to not miss lessons, in case of absence through illness to give the information.

5. The missed lessons to fulfill in time determined by the teacher.

6. In case of default of tasks the final estimation is reduced.

7. To attend daily at lessons.

8. To participate in educational process.

9. To do diligently home works.

10. To be tolerant, open, frank both easygoing to teachers and fellow students.

11. To support constructively a feedback on lessons.

12. To promote collective work and involving in discussion of more timid students.

13. To be punctual and obligatory.

14. To avoid the miss of lessons for the disrespectful reasons.

15. To exclude smoking in educational rooms.

11. A politics of the academic behavior and ethics.

The politics of the academic behavior and ethics is based on regulations of high school, the ethical code of students, namely:

• to be easygoing with teachers, colleges and comrades;

• to participate in all educational actions of university, institute;

• to support a culture of behavior at university;

• to observe cleanliness in rooms

 

ВОПРОСЫ ВХОДНОГО КОНТРОЛЯ

для студентов 4 курса по дисциплине «ЭППиПН»

 

Какие производства являются источниками вредных выбросов в атмосферу?

Классификация атмосферных выбросов

Характеристика твердых выбросов в атмосферу

Характеристика жидких вредных источников

Характеристика газообразных вредных выбросов

Какой урон приносят сточные воды, содержащие вредные компоненты?

Что подается на факел с НПЗ?

Какие методы снижения выбросов углеводородов в атмосферу  вы знаете?

Какие источники загрязнения окружающей среды бывают  при хранении нефтепродуктов?

Какими методами можно очистить сточные воды?

Что такое ПДВ?

Что такое ПДК?

Какие меры принимают контролирующие органы по номированию выбросов?

Что такое «кислотные дожди» ?

Что такое «захоронение отходов» ?

Что такое «оборотное водоснабжение» ?

Как решаются экологические проблемы в странах СНГ при совместных разработках нефтяных месторождений?

Имеются ли нарушения экологической обстановки при разработке нефтяных скважин?

Влияют ли нарушения экологии на флору и фауну страны?

Какие нарушения бывают на морях и реках вблизи нефтяных разработок?

 

 

 

Лектор:

 

Ст.преподаватель                                          Абдухаликова И.Р.

 

 

      Department:           TOGP           

      Lectures:  45, IWST:  45,  course:  4, group:  Сh-Т-06-7ка2

      The lecturer: Аbdukhalikova  I.R.

 

Month

September

Oktober

November

December

Week numbers

1.09.-05.09.

07.09.-12.09.

14.09.-19.09.

21.09-26.09

28.09.-03.10.

05.10-10.10.

12.10-17.10

19.10-24.10.

26.10-31.10.

02.11.-07.11.

09.11.-14.11.

16.11-21.11.

23.11-28.11.

30.12.-05.12.

07.12-12.12.

week

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

Inlet control (max / min)

4/2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

practice.(max / min)

 

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

2/1

IWS (max / min)

 

 

 1/0,5

 1/0,5

 

  1/0,5

  1/0,5

  1/0,5

 

  1/0,5

 1/0,5

1/0,5

 

  1/0,5

1/0,5

 

 

IWSТ (max / min)

 

 1/0,5

 1/0,5

 

  1/0,5

  1/0,5

  1/0,5

 

  1/0,5

 1/0,5

1/0,5

 

  1/0,5

1/0,5

 

 

Border task (max / min)

 

 

 

2/1

 

 

 

2/1

 

 

 

2/1

 

 

2/1

Marks: max

            min

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

4/2

Total control max / min)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

60/30